Cisco Catalyst 9120AX series Access Point, internal antennas, WiFi6 4x4:4 MIMO, H Domain C9120AXI-H Ethernet Wireless Access Point

C9130AXI-H Specification

Software

9130AXI

•Unified Wireless Network Software Release 8.10.x or later

•IOS  XE Software Release 16.12.1 with AP Device Pack, or later

Supported wireless LAN controllers

•9800 Series Wireless Controllers

•3504, 5520, and 8540 Wireless Controllers and Virtual Wireless Controller

802.11n version 2.0 (and related) capabilities

•4x4 MIMO with four spatial streams

•Maximal Ratio Combining (MRC)

•802.11n and 802.11a/g

•20- and 40-MHz channels

•PHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)

•Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive)

•802.11 Dynamic Frequency Selection (DFS)

•Cyclic Shift Diversity (CSD) support

802.11ac

•8x8 downlink MU-MIMO with eight spatial streams

•MRC

•802.11ac beamforming

•20-, 40-, 80-, and 160-MHz channels

• PHY data rates up to 6.9 Gbps (160 MHz with 5 GHz)

• Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)

•802.11 DFS

•CSD support

•WPA3 support

802.11ax

•8x8 uplink/downlink MU-MIMO with eight spatial streams

•Uplink/downlink OFDMA

•TWT

•BSS coloring

•MRC

• 802.11ax beamforming

•20-, 40-, 80-, and 160-MHz channels

•PHY data rates up to 10 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz)

•Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)

•802.11 DFS

•CSD support

•WPA3 support

Integrated antenna

•2.4 GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth

•5 GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth

External antenna with Smart antenna connector

•The 9130AXE Access Point is certified for use with antenna gains up to 13 dBi (2.4 GHz and 5 GHz)

•Offers the industry's broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios

•Supports Self-Identifiable Antennas (SIA) on the Smart antenna connector

•Smart antenna connector is a compact multi-RF connector with 8-DART interface

•Requires the AIR-CAB002-D8-R= 2-fppt smart antenna connector when used with antennas with a RP-TNC connector

•Requires the AIR-CAB003-D8-N= 3 ft smart antenna connector when used with AIR-ANT2513P4M-N= antenna

Interfaces

•1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz

•Management console port (RJ-45)

•USB 2.0 at 4.5W (enabled via future software)

Indicators

•Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors

Dimensions (W x L x H)

• Access point (without mounting brackets):

- C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm)

Environmental

9130AXI

•Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)

•Nonoperating (storage) altitude test: 25C, 15,000 ft (4600 m)

•Operating temperature: 32° to 122°F (0° to 50°C)

•Operating humidity: 10% to 90% (noncondensing)

•Operating altitude test: 40C, 9843 ft (3000 m)

Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 8x8 to 4x4 on the 5 GHz radio, uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled.

System memory

•2048 MB DRAM

•1024 MB flash

Warranty

Limited lifetime hardware warranty